- 您现在的位置：买卖IC网 > Sheet目录872 > P048T048M24AL (Vicor Corporation)V.I CHIP PRM REGULATOR 48V 240W
Not Recommended for New Designs
Pin / Control Functions
+In / -In DC Voltage Ports
V?I Chip Regulator
The V?I Chip maximum input voltage should not be exceeded. PRMs
have internal over / undervoltage lockout functions that prevent
operation outside of the specified input range. PRMs will turn on when
the input voltage rises above its undervoltage lockout. If the input
voltage exceeds the overvoltage lockout, PRMs will shut down until the
overvoltage fault clears. PC will toggle indicating an out of bounds
condition.
AL Version
VH
SC
SG
OS
NC
CD
+OUT
A
B
C
D
E
F
G
H
J
4
3
2
1
A
B
C
D
E
F
G
H
J
VC
PC
TM
IL
NC
PR
+IN
K
L
K
L
+Out / -Out Factorized Voltage Output Ports
These ports provide the Factorized Bus voltage output. The –Out port is
–OUT
M
N
P
M
N
P
–IN
connected internally to the –In port through a current sense resistor.
The PRM has a maximum power and a maximum current rating and is
Bottom View
protected if either rating is exceeded. Do not short –Out to –In.
VC – VTM Control
The VTM Control (VC) port supplies an initial V CC voltage to
downstream VTMs, enabling the VTMs and synchronizing the rise of
the VTM output voltage to that of the PRM. The VC port also provides
feedback to the PRM to compensate for voltage drop due to the VTM
output resistance. The PRM’s VC port should be connected to the VTM
VC port. A PRM VC port can drive a maximum of two (2) VTM VC ports.
PC – Primary Control
The PRM voltage output is enabled when the PC pin is open circuit
(floating). To disable the PRM output voltage, the PC pin is pulled low.
Open collector optocouplers, transistors, or relays can be used to
control the PC pin. When using multiple PRMs in a high power array,
Signal Name
+In
–In
VC
PC
TM
IL
PR
VH
SC
SG
OS
CD
+Out
–Out
Figure 15 — PRM pin configuration
Designation
G1-K1,G2-K2
L1-P1, L2-P2
A1,A2
B1, B2
C1, C2
D1, D2
F1, F2
A3, A4
B3, B4
C3, C4
D3, D4
F3, F4
G3-K3, G4-K4
L3-P3, L4-P4
the PC ports must be tied together to synchronize their turn on.
During an abnormal condition the PC pin will pulse (Fig.12) as the PRM
initiates a restart cycle. This will continue until the abnormal condition
is rectified. The PC should not be used as an auxiliary voltage supply,
nor should it be switched at a rate greater than 1 Hz.
TM – Factory Use Only
IL – Current Limit Adjust
The PRM has a preset, maximum, current limit set point. The IL port
may be used to reduce the current limit set point to a lower value. See
“adjusting current limits” on page 10.
PR – Parallel Port
The PR port signal, which is proportional to the PRM output power,
supports current sharing of two PRMs. To enable current sharing,
PR ports should be interconnected. Steps should be taken to minimize
coupling noise into the interconnecting bus. Terminate this port with a
10 k equivalent resistance to SG, e.g. 10 k for a single PRM, 20 k each
for 2 PRMs in parallel, 30 k each for 3 PRMs in parallel etc.. Please
consult Vicor Applications Engineering regarding additional
considerations when paralleling more than two PRMs.
VH – Auxiliary Voltage
VH is a gated (e.g. mirrors PC), non-isolated, nominally 9 Volt,
regulated DC voltage (see “Auxiliary Pins” specifications, on Page 7)
that is referenced to SG. VH may be used to power external circuitry
having a total current consumption of no more than 5 mA under either
transient or steady state conditons including turn-on.
SC – Secondary Control
The load voltage may be controlled by connecting a resistor or voltage
source to the SC port referenced to SG. The slew rate of the output
voltage may be controlled by controlling the rate-of-rise of the voltage
at the SC port (e.g., to limit inrush current into a capacitive load).
SG – Signal Ground
This port provides a low inductance Kelvin connection to –In and
should be used as reference for the OS, CD, SC,VH and IL ports.
OS – Output Set
The application-specific value of the Factorized Bus voltage (Vf) is set
by connecting a resistor between OS and SG. Resistor value selection is
shown in Table 1 on Page 2, and described on Page 9. If no resistor is
connected, the PRM output will be approximately one volt. If set
resistor is not collocated with the PRM, a local bypass capacitor of
~200 pF may be required.
CD – Compensation Device
Adaptive Loop control is configured by connecting an external resistor
between the CD port and SG. Selection of an appropriate resistor value
(see Equation 2 on Page 9 and Table 1 on Page 2) configures the PRM
to compensate for voltage drops in the equivalent output resistance of
the VTM and the PRM-VTM distribution bus. If no resistor is connected
to CD, the PRM will be in Local Loop mode and will regulate the
+Out / –Out voltage to a fixed value.
vicorpower.com
800-735-6200
V?I Chip Regulator
P048F048T24AL
Rev. 3.9
Page 8 of 14
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
P048T048T12AL
V.I CHIP PRM REGULATOR 48V 120W
P081N-271F2CBR10K
POT MODULE 8MM 10K SIDE ADJ
P090L-02T20BR50K
POT ROTARY 50K OHM 9MM SNAPIN
P092N-QC15AR20K
POT ROTARY 20K OHM 9MM
P110KH1-0F25BR10K
POT ROTARY 10K OHM 11MM BUSHING
P120K-F20BR5K
POT ROTARY 5K OHM 12MM SGL INS
P1330-105K
INDUCTOR POWER 1000.0UH SMD
P13SMNFLS473MA
POT 47K OHM 1.5W 20% SEALED
相关代理商/技术参数
P048T048T12AL
功能描述:V.I CHIP PRM REGULATOR 48V 120W RoHS:是 类别:电源 - 板载 >> DC DC 转换器（分解式） 系列:V-I Chip™, PRM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块 输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V） 应用:商用 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:模块 尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） 包装:托盘 工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）
P048T048T24AL
功能描述:V.I CHIP PRM REGULATOR 48V 240W RoHS:是 类别:电源 - 板载 >> DC DC 转换器（分解式） 系列:V-I Chip™, PRM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块 输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V） 应用:商用 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:模块 尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） 包装:托盘 工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）
P049-010
制造商:Tripp Lite 功能描述:TRIPPLITE - Bulk 制造商:Tripp Lite 功能描述:POWER CORD IEC 320/NEMA 5-20P 制造商:Tripp Lite 功能描述:POWER CORD, IEC 320/NEMA 5-20P, BLK, 10F 制造商:Tripp Lite 功能描述:POWER CORD, IEC 320/NEMA 5-20P, BLK, 10FT, 20A; Voltage Rating:125V; Cable Length - Imperial:10ft; Cable Length - Metric:3.05m; Connector Type A:IEC 320 C19; Connector Type B:NEMA 5-20P; Jacket Color:Black; Cable Assembly Type:Power ;RoHS Compliant: Yes
P049-01369-03
制造商:LG Corporation 功能描述:SPEAKER
P-04AF-L22K2
制造商:Panasonic Industrial Company 功能描述:BATTERY
P04NZ-032
制造商:SUMIDA 制造商全称:Sumida Corporation 功能描述:PFC Choke Coil
P04P2F-F
制造商:TE Connectivity 功能描述:
P04P5.5E-H
制造商:TE Connectivity 功能描述: